Drywall Anchors: Secrets Revealed!

Posted on June 15, 2019

Whether you’re hanging a picture or mounting a television, anything that goes on your wall needs something to anchor it in place. If there’s a stud in the wall that you can attach it to then you’re fine; you’ve got well-supported wood to drive a screw into which will hold whatever you’re mounting in place. If you can’t find a stud where you need one, though, you could have a problem. That’s where drywall anchors come in.

What Is a Drywall Anchor?

Drywall anchors are small pieces that are slightly larger than the screws you’re using on a project. Depending on the type of anchor you’re using it might be made of plastic or metal, with small fins sticking out from the outside of the anchor body and a hole in the middle that runs the length of the anchor. The anchors go into the wall, then your screw goes into the hole. As you screw it in, the screw digs into the anchor body in much the same way it would with wood to ensure that the screw won’t slip out.

Anchors are designed to provide a tight fit for your screws. As the screw goes in, the anchor is forced to spread out and open up a bit. This pushes the body of the anchor against the sides of the hole you put it in, causing those little fins to dig into the surrounding drywall. The fins are positioned to go in easy but resist coming out, giving you a solid mounting even though there isn’t any wood or other solid material for your screws to secure to.

Plastic Anchors

There are multiple types of drywall anchors. Choosing the right one for the job you’re working on helps to reduce unnecessary damage to your drywall and ensures that the mounting is strong enough for the load it needs to bear. To ensure that you have the right drywall anchor for what you need to support, try to get an estimate of the weight of the load and check the packaging of different drywall anchors to find an anchor that can hold that much weight.

If you have a relatively light load, you’ll probably need a plastic anchor. The most common of these are known as expansion anchors and are essentially plastic sleeves that you hammer into a drilled hole and that simply spread out as you insert a screw. There are also threaded plastic anchors that look like oversized screws; they work similarly, except you screw them into place instead of hammering them. Regardless of the type of plastic anchor you use, the purpose is still to dig into the drywall and hold a screw in place.

Metal Anchors

For heavier loads you’ll likely wind up with a metal anchor. Though you may see some threaded metal anchors, the most common metal anchors are known as molly bolts and feature a metal sleeve with a screw already inserted into them. You hammer these into place as you would with an expansion anchor, then remove the screw. Once you’re ready to mount you place the screw back into the anchor and start tightening; this causes a portion of the metal sleeve to pull toward the screw, expanding metal arms on the other side of the drywall to create a much more secure fitting.

If you have an even heavier load, you’ll need to use a toggle bolt instead. These anchors consist of a metal bolt with foldable metal wings that the bolt screws into. You have to fold the wings so that they lie over the bolt, then insert them into a hole large enough that they can fit through to the other side. Once on the other side the wings will expand, preventing the bolt from coming back out. Make sure that there is a washer or something else that’s large enough to cover the hole, though, or the bolt head could slip through the hole and you’ll lose your toggle bolt into the wall.

When Drywall Anchors Fail

In most cases, if a drywall anchor fails then it simply wasn’t the right type of anchor for the job. Trying to use smaller or weaker anchors for heavier loads will often result in failure because they simply don’t achieve enough grip on the surrounding material to hold the load. In some cases, though, the drywall itself may be too weak or the anchor you use may have been intended for a different material. Be sure to match the anchor to the weight and the material to minimize your chances of anchor failure.

For other great tips be sure and check out our friends at HomeKeepr!

Similar Posts

Landmark Fine Homes in OKC - A Woman Calculating Home Costs

Three Differences Between Custom Homes & Spec Homes

Published on May 15, 2023
Buying a new home is your chance to find a property that perfectly fits your needs and preferences. Two popular new construction options include custom homes and spec homes. While they are both brand new, these types of homes differ significantly. Learn more about custom homes vs. spec homes to help you make an informed […]
Read More
Landmark Fine Homes in OKC - A Hand Holding Dream Home In a Field

Is it cheaper to build a home if you already own the land?

Published on May 15, 2023
Building your dream home is an exciting and fulfilling experience. For many people, a surprisingly difficult part of custom home building is finding the right place to build. So you might feel lucky if you already have a plot or acreage. While it may be cheaper to build a home if you already own the […]
Read More
Landmark Fine Homes in OKC - Construction Worker Inspecting Siding on a House

How to Know If a New Home is Quality Constructed

Published on May 15, 2023
Buying a new home is one of the most significant investments you’ll ever make. It’s crucial to ensure your new home is quality constructed to avoid costly repairs and safety hazards in the future. Follow these steps to determine if your new home is built to a high standard. Check the Foundation The foundation is […]
Read More

Ready to Take a Tour of One of Our Custom Built Homes?

Contact Form - RED
crossmenu